SIMTOO XT175 Fairy Brushless Selfie Drone
My Experience of My SIMTOO XT175 Fairy Brushless Selfie Drone To the top: I apologize for the bad language of this story. My English skills are poor and that is why I have translated the text of this story Google Translate directly from Finland to English I decided to try the SIMTOO XT175 Fairy Brushless Selfie Drone, and I checked it out of the TomTop online store, from China to Finland My SIMTOO XT175 Fairy Brushless Selfie Drone's Flying History, when the package arrived to me, until I was finally destroyed by Dronen. First Fly: Fly with Remote Controller Fragile but relative, the place dominated in my own yard. YouTube Video of Flying: Fly. Android Apps: Phone: Samsung Galaxy S7 Edge The machine doesn't stay in control. The flight ends on the side of a neighbor's car. Obvious reason: Insufficient Satellite Connection. (From 8 to 9 satellites only is connect) Should be, (at least from the Fairy YouTube videos), combined with at least 10 satellites before all Fairys functions work, as described in the manual. Also, no (from the number of satellite connections), there is nothing in the manual. There are no more satellites in Seinajoki, Finland than 8 - 9 I waited for the satellites to be connected for about 15 min. Phone: Samsung Galaxy S7 Edge Second Flick: Combined with Drone Controller Connecting Fairy Drone and Remo Controller: Drone escapes from the hands, makes miracle moves and drops down the haystack. Dronen rotors rotate fully until I get rid of the drone battery. The obvious reason for this is: Controller calibration was not performed prior to flight and the controller roller gas switch was in the up position, i.e. full. Outcome of this flight: Dronen's one rotor comes off. Two rotor arms break and one of the rotor motors comes off: Glue all with epoxy adhesive. YouTube video: Third Flight: When I put a little gas on, the Fairy will swing right onto the right side and turn off. At least one reason: The battery disconnects and no longer stays in place without the need for a separate fixation Fourth Flying. The start goes fine, then I dare to fly the Quadcopter too far, and it will not return to itself. The battery power is low, nor does it return to itself, but when the power runs out, the Quadcopter drops down to the tree below it, knocking it out of a branch, knocking it down. YouTube video: Result: Again, the two rotor arms break. Again, epoxy adhesive has use Fairy weight after epoxy gluing YouTube video: Fifth Aviation. Fairy Drone escapes out of the air, as soon as I push the controller right pole switch litle upper, when I turned off the controller lock and the rotor blades rotate slowly. Pressing the home button and landing button did not help. The Fairy went up all the way up until one of the rotor motors came out, and the Fairy Drone fell down like a stone. I can't find rotor motor anymore for anything. YouTube video: This is the end of the situation. Now the whole story is told to the supplier of the item, and waiting for the answer is whether the reason alone is mine, or whether the inadequate instruction manual is part of the matter. The final conclusion and my own opinion All this would have been prevented by a good user manual. The instruction manual does not tell: The roller on the upper right corner of the controller does nothing. It's a gas switch. Lower position: Slow Upper: Fast YouTube video Remo Controller roller gas switch in upper right corner. The location is bad because when you put your smartphone on the Remo Controller phone holder unnoticed easily the hand hits the roller switch. Always check the position of the gas switch before starting to run the Fairy Drone Also, the Remote Controller calibration does not say anything in the manual. Calibration: When the controller is on and connected to the Quadcopter: Both control rods are pulled down and then further downward pulled out, whereby the light of the controller flashes and two beeps are heard. Now it is possible to control the Quadcopter in a controlled way with the controller. Controller calibration: YouTube video: Quadcopter not return home if the range is too long. Quadcopter does not return home if the battery is low, but slowly descends to where it is at the moment. That's what happened to me over the tree and my, SIMTOO XT175 Fairy Brushless Selfie Drone landed on the tree and slowly came to the ground from the branch by branch. In this case, the two rotor arms were broken. YouTube video: Fairy Drone does not stand fast and uncontrollable descent from high, it breaks. In particular, the rotor arms are susceptible to breakage. I myself would have saved about 100 € of money and 30 hours of time that I used to refurbish a broken Quadcopter after breakage, always to fly again. Now, my Fairy Drone should no longer be refurbished unless it receives a new rotor engine from something. I recommend this only to experienced flyers. Of course, use becomes easier if the manufacturer delivers the, SIMTOO XT175 Fairy Brushless Selfie Drone, comprehensive user manual. Greatings: Vesa Kultalahti Hyllykalliontie 5 A 2 60510 HYLLYKALLIO, SEINÄJOKI Finland